dali-2 & push dimmable constant voltage 100W 12V/24V led driver power supply for led strip
This DALI-2 series dimmable constant voltage 100w LED driver is integrated with the junction box, has built-in active PFC function, is easy and quick to install, and has short circuit/overload/over temperature protection functions. 7 years warranty
Specification
| Model | SMT-JB12100V-DP2-5C | SMT-JB24100V-DP2-5C | SMT-JB36100V-DP2-5C | SMT-JB48100V-DP2-5C | |
| Output | DC Voltage | 12V(12-13.5V) | 24V(24-26V) | 36V(36-38V) | 48V(48-50V) |
| Voltage Tolerance | ±0.2V | ||||
| Rated current | 8.34A | 4.17A | 2.78A | 2.08A | |
| Rated power | 100W | ||||
| Load Regulation | 2% | 1% | 1% | 1% | |
| Input | Voltage Range | 100-277VAC | |||
| Frequency Range | 47 - 63Hz | ||||
| Power Factor(Typ.)@ full load | PF≥0.98@120VAC PF≥0.96@230VAC PF≥0.95@277VAC | ||||
| THD(Typ.)@ full load | ≤10%@120VAC ; ≤10%@230VAC; ≤15%@277VAC (full load) | ||||
| Efficiency(Typ.)@ full load | 88.5%@120VAC 89.5%@230VAC/277VAC |
87.5%@120VAC 89.5%@230VAC/277VAC |
88%@120VAC 89.5%@230VAC/277VAC |
88%@120VAC 89.5%@230VAC/277VAC |
|
| Protection | AC Current(Max.) | 1.3A | |||
| No-load power Consumption(optional) |
1.15W(@120V) 0.95W(@230V) 1.05W(@277V) |
1.00W(@120V) 0.85W(@230V) 0.95W(@277V) |
1.10W(@120V) 0.95W(@230V) 1.05W(@277V) |
1.17W(@120V) 1.00W(@230V) 1.10W(@277V) |
|
| Standby power Consumption(optional) |
0.20W(@120V) 0.39W(@230V) 0.47W(@277V) |
0.25W(@120V) 0.42W(@230V) 0.47W(@277V) |
0.20W(@120V) 0.43W(@230V) 0.48W(@277V) |
0.20W(@120V) 0.43W(@230V) 0.48W(@277V) |
|
| Inrush Current (Typ.) | 23.2A,360us@50%Ipeak@120VAC;80.0A,104us@50%Ipeak@230VAC;54.0A,280us@50%Ipeak@277VAC | ||||
| Leakage current | <0.5mA | ||||
| Short Circuit | Hiccup mode, recover automatically after fault condition is removed | ||||
| Over Load | ≤120% ,hiccup mode, recover automatically after fault condition is removed | ||||
| Over temperature | case temp. over 100℃±10℃,output will be off; recovers automatically after temp. drops. | ||||
| Environ-ment | Working TEMP. | -40 ~ +70℃ (see below derating curve) | |||
| Working Humidity | 20 ~ 95%RH,non-condensing | ||||
| Storage TEM.,Humidity | -40 ~ +80℃,10 ~ 95%RH | ||||
| TEMP.coefficient | ±0.03%/℃(0 ~ 50℃) | ||||
| Vibration | 10 ~ 500Hz, 2G 10min./1 cycle,period for 60min. each along X,Y,Z axes | ||||
| Safety & EMC | Safety standards | EN61347-1 EN61347-2-13(EU) & UL8750(US) | |||
| Withstand voltage | I/P-O/P:1.80KVAC I/P-FG:1.8KVac O/P-FG:1.8KVac | ||||
| Isolation resistance | I/P-O/P:100MΩ/ 500VDC/ 25℃/ 70%RH | ||||
| EMC Emission | EN55015 EN61000-3-2-3(EU)≥50% Load & FCC Part 15 B (US) | ||||
| EMC Immunity | EN61000-4-2,3,4,5,6,11 EN61547 | ||||
| Others | Net Weight | 0.83kg/pcs | |||
| Dimension | 241*125*40mm (L*W*H) | ||||
| packing | Qty: 20cs/ctn; G.W: 18kg/ctn; Ctn size:300*280*215mm | ||||
| Notes | 1. All parameters NOT specially mentioned are measured at 230VAC input , rated load and 25℃of ambient temperature. | ||||
| 2. Tolerance: includes set up tolerance, line regulation and load regulation . | |||||
 |
 |
 |
 |
Mechanical Specification
※ Input & Output wiring
※Input electronic cable 3*18AWG, the green cable connect with (FG) ,Black with AC (L), White with AC(N) (US);
※Output : 12V electronic cable 3*16AWG to be connected to LED Light;
24V electronic cable 3*18AWG to be connected to LED Light;
※Dimming cable
※Dimming electronic cable 3*18AWG, Brown DA/N and Purple DA/L (No polar) connected to the DALI BUS when use DALI function.
Brown (N) is connected to AC (N) while Purple (L) and pink (CCT Push )connected to CCT Push dim switch dimmer( L) when use Push function.
※Please make sure you connect these correctly otherwise your product will not function correctly and could be damaged.
CCT (TW) dimming: electronic cable, Black is output ( V+) Positive, While (CW-) and Yellow (WW-) are output (V-) negative
Note: there is external antenna at output side. Don't disassemble!
Dimming operation
※Note: For DALI Dimming Wiring Diagram 3, please noted that only one DALI power is need in the DALI bus, so no extra DALI power is needed if the Master or Dimmer already includes the DALI Power.
DALI-2 address setting Operation
※The default address for the DALI-2 LED driver is 001.
※Address settings device:
※Address settings:
① RDM setting address:
Set the address by the RDM device. For detailed operation, please refer to RDM device instruction manual.
② NFC setting address:
The DALI-2 led drivers’ address can be read and written by a mobile with NFC APP or NFC handheld device (NFC read & write device: NFC-RW) by close to the NFC signal area of the DALI-2 LED drivers.
■ Adjust output voltage Operation
※Adjust output voltage slightly for DALI-2 LED drivers
1) La tension de sortie du pilote peut être lue et écrite par un mobile avec une application NFC ou un appareil portable NFC (périphérique de lecture et d'écriture NFC : NFC-RW) à proximité de la zone de signal NFC des pilotes de LED D ALI-2 .
2) Plage de tension : niveau 1 ~ 10, chaque niveau est de 0,2 V. Le niveau de tension de sortie par défaut est 1 .
Vol classé. |
Niveau 1 |
Niveau 2 |
Niveau 3 |
Niveau 4 |
Niveau 5 |
Niveau 6 |
Niveau 7 |
Niveau 8 |
Niveau 9 |
Niveau 10 |
12V |
12.00V |
12,16 V |
12,32 V |
12,48 V |
12,64 V |
12,80 V |
12,96 V |
13,12 V |
13,28 V |
13,50 V |
24V |
24.00V |
24,22 V |
24,44 V |
24,66 V |
24,88 V |
25,1 V |
25,32 V |
25,54 V |
25,66 V |
26,00V |
36V |
36,00V |
36,22 V |
36,44 V |
36,66 V |
36,88 V |
37,10 V |
37,32 V |
37,54 V |
37,66 V |
38,00V |
48V |
48,00V |
48,44 V |
48,44 V |
48,66 V |
48,88 V |
49,10 V |
49,32 V |
49,54 V |
49,66 V |
50,0 V |
■ Comment définir l'adresse du pilote de LED CV DALI-2 via l'application NFC ou le périphérique NFC ?
Opération simple de réinitialisation de l'adresse du pilote LED DALI-2 et de réglage de la tension de sortie par un mobile avec l'application NFC (définir NFC) ou un appareil portable NFC (appareil de lecture et d'écriture NFC : NFC-RW)
Produits connexes
Driver LED intelligent à intensité variable DALI-2 & PUSH 30 W 12 V. Conception de boîtier en aluminium, bonne dissipation thermique, mode de sortie PWM, plage de gradation entre 0,1 et 100 %. Convient aux projets d'éclairage LED intelligents extérieurs Mode : SMT-JB12030V-DP2 tension d'entrée: 100-265VAC Taille : 181*103.5*42mm |
